Female Hose Beginning
(Swivel End)
Use to attach ¾" mainline tubing to a faucet, hose end
or male hose end of a filter or adapter.
|
|
| |
Coupler
For joining ¾" mainline tubing or to repair a slit or
large hole in a mainline.
A necessary repair part.
Always have a few on hand.
|
|
| |
|
Reducing coupler. For joining ¾" tubing to ½" tubing.
|
| |
Male Hose End
Male hose threads.
Can be used to install a VFH flush valve
at the end of the mainline tubing.
|
|
| |
Male Hose End with Cap
This fitting is used to end a line.
The screw off cap makes it easy to flush lines.
|
|
| |
| |
Female Hose Plug
Protect your system from dirt and bugs when it is disconnected
from the water source (i.e. during winter shut down
or when alternating systems with a single water feed line).
Male hose thread for female hose beginning (ELFH34).
|
|
| |
Figure 8 End
The most common fitting used to end a line. Simply slip over the end of the line, bend the tubing over, and slip over the end again.
|
|
| |
Female Hose Tee
(Swivel End)
Attach to a hose or faucet where two ¾" mainlines are needed.
|
|
| |
Male Hose Tee
|
|
| |
Tee
Use to branch off ¾" mainline tubing.
|
|
| |
Reducing Tees
Use the ELRT for branching a ½" line off of a ¾" line.
Use an ELRT12 at the end of a ¾" linE to split it into two ½" lines.
|
|
|
ELRT
|
Reducing Tee 3/4 x 3/4 x 1/2
|
| |
|
ELRT12
|
Reducing Tee 1/2 x 1/2 x 3/4
|
| |
Elbow
(90 degree bend)
To go around a corner that would otherwise kink the ¾" mainline.
|
|
| |
|
ELRL
|
Reducing Elbow 3/4 x 1/2
|
| |
Easy Loc Cross
|
|
| |
Easy Loc Reducing Cross
|
|
|
ELRX
|
1/2 x 1/2 x 3/4 x 3/4 Cross
|
| |
Easy Loc Valve
Inline valve for ¾" mainline tubing.
|
ELV34
|
| |
Easy Loc x PVC Pipe Thread
Easy Loc Valve with ¾" Male Pipe Thread
Inline valve for connecting ¾" mainline tubing to a ¾" PVC
female thread fitting.
|
|
|
EL34MPV34
|
3/4 EasyLoc
x 3/4 MP thread Valve
|
| |
¾" Male Pipe End
|
|
|
EL34M34
|
3/4 EasyLoc
x 3/4 Male Pipe
|
| |
¾" Female Pipe End
|
|
|
EL34F34
|
3/4 EasyLoc
x 3/4 Female Pipe
|
| |
3/4" Easy Loc x 1" PVC
3/4" Easy Loc part to make Easy Loc reducing tees.
Will glue INTO any 1" PVC socket.
|
|
| |
¾" Easyloc Tee x ½" Female Pipe Tee
Use to attach ¾" mainline tubing to any ½" PVC male pipe thread outlet. Not a swivel.
|
|
|
EL12FT34
|
1/2 Female Pipe x 3/4 EasyLoc Tee
|
| |
Easy Loc to PVC Adapters
Make your own Easy Loc Fittings.
Simply glue these adapters into standard ¾" PVC slip
fittings.
Often used in a PVC Tee to branch off to ¾" poly mainline tubing.
|
|
| |
1" Easy Loc (for use with 1"
Flatube™)
1" Easy Loc Female Hose Beginning
(Swivel End)
Use to attach 1" Flatube to a faucet, hose end
or male hose end of a filter or adapter.
|
|
|
ELFH1
|
1in EL x Female Hose
|
| |
1" Easy Loc Coupler
For joining 1" Flatube tubing or to repair a slit or
large hole in a mainline.
A necessary repair part.
Always have a few on hand.
|
|
| |
1" Easy Loc x ¾" Easy Loc Reducing Coupler
For joining 1" Flatube tubing to ¾" Polyethylene tubing
branch line.
|
|
|
ELRC134
|
1in x 3/4in EL Reducing Coupler
|
| |
1" Easy Loc Male Hose End with Cap
This fitting is used to end a line.
The screw off cap makes it easy to flush lines.
|
|
| |
1" Easy Loc Elbow
(90 degree bend)
To go around a corner that would otherwise kink the ¾" mainline.
|
|
| |
1" Easy Loc Tee
Use to branch off 1" Flatube tubing.
|
|
| |
1" x 1" x 1/2" Easy Loc Reducing Tee
Use to branch off 1" Flatube tubing to 1/2" tubing.
|
|
| |
1" x 1" x 3/4" Easy Loc Reducing Tee
Use to branch off 1" Flatube tubing to 3/4" tubing.
|
|
| |
1" Easy Loc x 1" MPT
1" Easy Loc by 1" Male Pipe Thread (MPT) inlet
to connect Flatube to a 1" FPT connection.
|
|
| |
1" Easy Loc x 1" PVC
1" Easy Loc part to make Easy Loc reducing tees.
Will glue INTO any 1" PVC socket.
|
|
| |
1" Easy Loc x 1" PVC Slip
1" Easy Loc with 1" PVC slip inlet to connect to a 1" PVC pipe.
This part goes OVER the 1" PVC part.
|
|
|
EL1SOC
|
1in EL x 1in PVC Socket
|
| |
|
|
Emitters 
Calculators 
Checkout 
These ¾" lock ring fittings are easier to use than compression
and can be removed and re-used.
