Hose and Quick Connects
 Catalog Page 35

An inline ball valve for shutting off individual rows in a garden or for breaking up a larger area into smaller systems.

Split your faucet and use either line or both at once.   Put a drip system on one side and still keep one line open for hose use or switch from one drip area to another by switching valves.

This brass hose Y will allow the full flow of your faucet to pass through without the restriction that occurs with the HYV or HYVBR.

In places where there is no room to use a Hose Y or if you need the water supply to go in opposite directions, the Hose Tee is the answer.   Black plastic construction with female hose swivel inlet by male hose thread outlets.

Full flow PVC splitter made by DripWorks for multiple timers.   Has a brass hose swivel for added strength.   NOTE: Do not hang multiple timers from a faucet.   Use an EXTENSION HOSE (see below) to situate the splitter on the ground to prevent stress damage.

A heavy duty brass body with built-in valves and hose swivel.   It is designed for up to 3 battery operated timers and a hose.   Comes with wall brace for extra support.   We are very impressed with the quality and strength of these units.   10 year warranty.

Many times in designing a system there is a need to use a faucet located beneath a deck, or a valve assembly is too large to attach directly to a faucet and must be placed on the ground.   With an extension hose you simply move the water supply to a more convenient location and add a HSO (above) to have a remote shut off.   This heavy-duty hose is rated to 200 PSI burst strength. (HPEX8 will be available for a limited time only)

Protect your timer by installing the 8 inch spring wound hose between your faucet and timer.

Use this when you need to attach fittings to a low faucet where there is no room to work.   Has standard hose ends.

Attach the female (waterstop) end of this set to the male end of any hose to stop water flow while changing hoses, nozzles, or sprinklers.   When the fittings are disconnected, the water stops immediately.   As soon as the ends are reconnected, the water flow starts.   YOU NEVER HAVE TO GO BACK TO THE FAUCET TO SHUT OFF THE WATER!

Extra male ends to put on each hose, nozzle, and hose end sprinkler.   Combine with a female waterstop end for an in-line connection.   Primarily used with HStopBR.

This two-part set is used to quickly switch different hoses to the same faucet.   The female end stays permanently on the faucet while a male end is attached to the end of each hose.

Attach the female (waterstop) end of this set to the male end of any hose to stop water flow while changing hoses, nozzles, or sprinklers.   When the fittings are disconnected, the water stops immediately.  As soon as the ends are reconnected, the water flow starts.   YOU NEVER HAVE TO GO BACK TO THE FAUCET TO SHUT OFF THE WATER!

Converts the male end of a hose bib or garden hose to a quick connector. Does not have a water stop.

Extra male ends to put on each hose, nozzle, and hose end sprinkler.   Combine with a female waterstop end for an in-line connection.  Used with HStopSET or HCSET.

Extra female ends to put on a hose to connect to another hose.   Combine with a male waterstop end for an in-line connection.

Extra male ends to put on a hose to connect to another hose.   Combine with a female waterstop end for an in-line connection.

A great price for a combination Hose Y (non-swivel) and two quick connects. The disconnect portion is identical to the HMTAP. Shut offs are built into the Hose Y.

Perfect introduction to Quick Connects. You get an HCSET, an HTAPSET and an HMHA all at a special low price.