|
For attaching T-Tape to mainline tubing.
Simply punch a 1/4" hole (PUY punch) in the mainline,
connect the T-Tape to the Tape Loc end and insert the barbed
end into the punched hole.
This fitting allows a flow of over 80 GPH at 10 PSI.
|
|
LSB
|
| 1-49 | $0.60 | Each |
| 50+ | $0.58 | Each |
| |
|
|
For connecting 2 sections of T-Tape or repairing a line.
Always have a few of these on hand.
|
|
LSC
|
| 1-49 | $0.85 | Each |
| 50+ | $0.832 | Each |
| |
|
|
A tapered sleeve to end rows.
Slip T-Tape through the narrow side, fold over
three times and pull back on the feeder end.
Wedges tight!
|
|
LSGS
|
| 1-99 | $0.28 | Each |
| 100+ | $0.25 | Each |
| |
|
|
For shutting off individual lines.
The 1/4" barb has a flow of over 80 GPH at 10 PSI.
|
|
LSBSO
|
| 1-9 | $2.05 | Each |
| 10-49 | $1.90 | Each |
| 50+ | $1.71 | Each |
| |
|
|
For shutting off individual lines. The valve can be put directly
into a run of T-Tape. Doesn't have the flow restriction of the LSBSO.
The valve is easy to use and simple to install.
|
|
LSCSO
|
| 1-49 | $1.95 | Each |
| 50+ | $1.80 | Each |
| |
|
|
When teeing off of PVC or large poly pipe, use this
for a removable row beginning with a valve to allow
an individual row to be turned off.
Doesn't have the flow restriction of the LSBSO.
|
|
LSV12M
|
| 1-49 | $1.95 | Each |
| 50+ | $1.71 | Each |
| |
|
|
For attaching T-Tape to the end of 1/2" mainline tubing.
|
|
| |
|
For attaching T-Tape to a hose or hose bib or any other
male hose threads.
|
|
| |
|
For running T-Tape directly off a PVC header.
Glues onto 1/2" PVC pipe or into a 3/4" PVC fitting.
|
|
LSSOC
|
| 1-49 | $0.90 | Each |
| 50+ | $0.884 | Each |
| |
|
|
When teeing off of PVC or large poly pipe, use this
for a removable row beginning.
Ideal for long runs.
|
|
LS12M
|
| 1-49 | $0.80 | Each |
| 50+ | $0.78 | Each |
| |
|
|
An end with a hose cap which makes it easy to flush lines.
|
|
| |
|
An end with a male hose thread end.
|
|
| |
|
For making sharp turns in a garden.
Remember, T-Tape will not go around a 90 degree corner.
|
|
| |
|
To branch off an additional line of T-Tape.
|
|
| |
High Flow Barbs
These Tape Loc fittings have a very large (.400) barb which
allows for a greater flow, useful for longer runs.
They can only be used with 3/4" or larger flexible
mainline tubing or poly pipe.
Use the
.400 Punch
or drill a 5/16" hole in the
wall of the tubing to insert the barb.
|
|
|
A large barb for long runs of T-Tape.
At 12 PSI the flow is approximately 300 GPH.
|
|
LSB400
|
| 1-49 | $0.60 | Each |
| 50+ | $0.58 | Each |
| |
|
|
For connecting to 1" or larger PVC.
Drill a 9/16" hole in the PVC and insert the grommet first.
Then insert the barb into the grommet.
|
|
LSGRO
|
| 1-49 | $0.95 | Each |
| 50+ | $0.936 | Each |
| |
|
|
This high quality valve allows you to shut off
individual rows quickly and easily.
Use the PU400 punch and insert the barbed end
into the tubing.
Turn the locking nut counter clockwise to secure
the barb to the tubing.
Makes a tight seal.
|
|
| |
|
For shutting off individual lines.
|
|
LSBSO400
|
| 1-49 | $2.05 | Each |
| 50+ | $1.71 | Each |
| |
|
This is a newer, lower cost version of our PU400. It is a punch for the higher flow .400 barbs and it is an insert tool for the commercial tape beginning (LSB400). The punch tip is hardened steel, amazingly sharp and is molded into a solid plastic handle. It comes with a plastic cover to protect both the tip and the user. To use it as an insert tool just slide the LSB400 over the shaft and push the tool into the mainline tubing (3/4” or larger). Give the tool a slight twist and it will punch a hole and insert the LSB400 at the same time. Once the barb is seated in the main line, just remove the tool and move on to the next row. It takes less than 10 seconds per insertion.
More Information
|
|
| |
|
A large goof plug to repair a hole in mainline tubing made for a high flow barb.
|
|
| |
|
To connect a 3/8" barb into 1" or larger PVC pipe.
Rubber grommet makes a water tight seal.
Drill a 9/16" hole in the PVC.
|
|
| |
Grommet Drill Bit
Multi-step cone drill bit cuts 1/4" - 3/4" holes in 1/16" gradients. Will not crack or shatter PVC. Made of high speed steel.
|
Click To Enlarge
|
| |
Emitters 
Checkout 
Call 
