Baccara In-line Valves
The only valve that works with low pressure and low flow.
Baccara valves have a large pressure range of 4.3 to 140 PSI and
a very low head loss at high flow rates.
They also feature manual override, flow control and progressive opening and shut off
that prevents water hammer.
Their efficient design and advanced technology plastics make the
valves strong with very low maintenance.
|
VBAC34
VBAC112
VBAC2
VBACSOL
|
|
VBAC34
|
3/4" valve .5-22 GPM
|
| |
| |
|
VBAC112
|
1 1/2" valve 30-120 GPM
|
| |
|
VBAC2
|
2" valve 40 - 140 GPM
|
| |
|
VBACSOL
|
Replacement Solenoid
|
| |
|
VBACDIA34
|
Replacement Diaphram for 3/4", 1" Baccara
|
| |
Baccara Valves
Head loss for fully open valve
|
|
Orbit In-line Valves
An economical low flow valve that has similar features
to the Rainbird valves but will operate at lower pressures.
The 1 1/2" and 2" valves have flow control and
are a great value.
|
VOR34/VOR1
|
|
VOR34
|
3/4" valve
.1 - 22 GPM
|
| |
| |
Hunter Jar Top Valve
Professional Quality
This is the perfect valve for people who believe system maintenance
should be simple.
Most valves fail because of debris inside the valve.
With a simple twist, the top of the valve will unscrew and the valve
can be inspected and cleaned if necessary.
NO TOOLS NEEDED!
1" FPT inlet and outlet
|
|
|
VHJAR
|
1" valve .2 - 30 GPM, 20-150 PSI
|
| |
Rainbird Inline Valve
The Rainbird Inline valve is designed for below ground
installation (inside a valve box).
This is a professional series valve with a
minimum flow of .2 GPM (12 GPH) and with a pressure
range of 15-150 PSI.
3 Year Warranty.
|
|
|
VRB34
|
3/4" valve
.2 - 22 GPM
|
| |
| |
Rainbird Anti-Siphon Valve
This is the only anti-siphon valve we have found
designed specifically for drip irrigation.
It has the same flow rate and pressure rating
as the Rainbird Inline valve above.
3 year warranty.
NOTE: The top of the valve should be 6" above
the highest emitter in the system.
|
|
|
VRBAS34
|
3/4"
Anti-Siphon
valve
|
| |
|
VRBAS1
|
1"
Anti-Siphon
valve
|
| |
Valve Assemblies
Faucet to Valve Setup
This manifold system comes assembled, teflon-taped and ready to attach to your faucet.
Extra valves can easily be added using the TMBVHAD.
You will need to add connectors (below) and a length of Direct Burial Wire (below)
from your timer to the valves.
You may also need filters and regulators.
The set up includes a 5' length of high pressure hose (HPEX5),
and all the parts including a 3/4" valve.
We adapt the outlet of the valve to male hose thread.
|
TMBVHST
TMBVHAD
|
|
TMBVHST
|
Manifold start
with Baccara 3/4" valve
|
| |
|
TMBVHAD
|
Additional
Baccara 3/4" valve setups
|
| |
Olson Waterwell Valve Assembly
Combining economy with convenience, the Olson WaterWell multi-valve
assembly eliminates the need to purchase and assemble the many
components formerly required to install multiple automatic 1" control
valves.
Available with from 2 to 6 valves, the valve assembly is factory built
and factory tested, ready to connect to power and water sources.
Features:
- Saves hours of expensive installation labor
- Pre-tested before it leaves the factory
- Compact, professional and convenient
- Easily connects to an automatic irrigation controller
- Up to six 1" valves in one standard box
- Flow Range: .5 to 30 GPM
- Pressure Range: 20 to 200 PSI
- Use with PVC glue
- 2 Valve Box (round) Dim.:12" L x 12" W x 11" H
- 3-6 Valve Box (rectangular) Dim.:17" L x 12" W x 12" H
|
|
| VOM2 - 2 valves |
|
| VOM3 - 3 valves |
| | VOM4 - 4 valves |
|
|
VOM2
|
2 Way Manifold in Valve Box
In: 1 x 1" Pipe, Out: 2 x 1" Pipe
|
| |
|
VOM3
|
3 Way Manifold in Valve Box
In: 1 x 1" FPT, Out: 3 x 1" MPT
|
| |
|
VOM4
|
4 Way Manifold in Valve Box
In: 1 x 1" FPT, Out: 4 x 1" MPT
|
| |
|
VOM6
|
6 Way Manifold in Valve Box
In: 1 x 1" FPT, Out: 6 x 1" MPT
|
| |
Valve Boxes
These rigid plastic boxes have snap-on lids used for
easy access to valves and fittings placed below ground.
|
|
|
VB6
|
9" base
7" top diam.
9" high
|
| |
|
VB12
|
16"x21 1/2" base
11 3/4"x17" top
12" high
|
| |
|
VB20
|
20"x26 1/2" base
15"x21" top
12 1/2" high
|
| |
Automatic Distribution Valves
High Flow Only
These valves serve a unique need for large sprinkler or farm drip systems.
They enable one high flow battery timer, such as the
TDGHF, the
Dig battery timers or any of our
electric timers with a
valve to water up to six zones with one valve.
Every time the water shuts off, the distributor switches to the next outlet.
The watering time for each outlet can vary and is dependent upon the controller
and not the distribution valve.
The cams can be easily changed to increase or decrease the number of zones
to be watered.
There is a small amount of water flow between the outlets when the
system is operating.
Automatic Distribution Valves are very reliable and will last for years.
They are easily serviced, having only one moving part and eight total parts.
Operating Requirements:
- Pressure Range: 25-75 PSI
- Must be installed at the highest point in the system
- Any outlet not used must have a 12" long pipe glued
into it with a cap on the end and a 1/8" hole drilled into it for draining
- There must be a minimum 30 second delay between the
end of one watering cycle and the beginning of the next (time is needed for the
pressure to dissipate and the cam to advance
- The body of the valve is ABS. Use All Purpose Cement
for gluing PVC fittings to it. The glue must sit for 12 hours before
pressurizing the system.
|
|
Four Outlet Valve - without Cam
1 1/4" Inlet, 1 1/4" Outlet - All fittings are female slip.
Flow Range: 10-40 GPM
2, 3 or 4 Zone Operation
IMPORTANT!!
You must purchase one valve and one cam to make a complete unit.
|
|
| |
Cams for Four Outlet Valves
|
|
|
VDV4C2
|
2 Zone Cam
(works with the 4 or 6 outlet valve)
|
| |
| |
| |
Six Outlet Valve - without Cam
1 1/4" Inlet, 1" Outlet - All fittings are female slip.
Flow Range: 10-25 GPM
2, 3, 4, 5 or 6 Zone Operation
IMPORTANT!!
You must purchase one valve and one cam to make a complete unit.
|
|
| |
Cams for Six Outlet Valves
|
|
|
VDV4C2
|
2 Zone Cam
(works with the 4 or 6 outlet valve)
|
| |
| |
| |
| |
| |
Rain Sensor and Pump Start Relay
Rain Sensor - Normally Closed
The Mini-Clik rain sensor has moisture absorbing disks
that swell during rain then shrink during dry periods.
This makes the Mini-Clik more accurate than other
style sensors.
It can be adjusted for either 1/3", 1/4", 1/2",
3/4" or 1" of rain.
This sensor will work with any of our electric timers.
|
|
|
TMS
|
Mini-Clik rain sensor
|
| |
Pump Start Relay
This relay starts a pump when your controller turns on.
It works with any controller that has a Pump Start
or a master control valve.
Maximum pump size is 2 HP, either 120V or 240V.
Has an all weather box for both indoor and outdoor use.
|
|
| |
Wire Connectors
Blue Gel-Filled Connectors
NEW!!
These are the easiest way to connect 2 or 3 wires together
making a waterproof connection between valves and timers.
No tools necessary.
NO STRIPPING OR TWISTING OF WIRES IS NECESSARY.
|
|
| |
|
Instructions
|
Gel-Filled Connectors
Limited to stock on hand
A silicon filled connector for 2 or 3 wires to make
permanent, waterproof electrical connection between
valves and timers.
Use pliers to clamp down and create a solid connection.
NO STRIPPING OR TWISTING OF WIRES IS NECESSARY.
|
|
| |
Multi Splice Enclosure
This enclosure is designed for multiple splices in wet
or underground locations.
It has a special grease filling and cap for up to
four connections.
Just connect the wires with wire nuts, insert
into the grease filling and snap shut.
|
|
| |
Scotchlok Connectors
Wire nuts for joining small gauge wires together.
Connect two or three 18 gauge wires in each.
|
|
| |
Direct Burial Wire - 18 Gauge
The only wire (solid core) recommended for automatic systems.
It can be used with or without conduit.
Low current requirements make it possible to have
wire runs of up to 500' between the valves and the controller.
One central controller can operate valves in many locations.
To determine the needed number of strands, count your
valves and add one wire for the common ground.
Thus three strand wire is designed for two valves
with a common ground, five strand wire is used for up to 4 valves.
NOTE: If there is any chance of adding a valve in the
future, it's a good idea to size the wire for that possibility now.
|
|
2 Strand Wire (1 Valve)
|
|
| |
| |
| |
| |
3 Strand Wire (up to 2 Valves)
|
|
| |
| |
| |
| |
4 Strand Wire (up to 3 Valves)
|
|
| |
| |
| |
| |
5 Strand Wire (up to 4 Valves)
|
|
| |
| |
| |
| |
7 Strand Wire (up to 6 Valves)
|
|
| |
| |
| |
| |
9 Strand Wire (up to 8 Valves)
|
|
| |
| |
| |
| |
13 Strand Wire (up to 12 Valves)
|
|
| |
| |
| |
|
|
Kits 
Checkout